Use appropriate Linux DTS to turn on corresponding Tibbit interface for sockets (will be done with a TPS configurator in the next software release).
| Tibbit # | Description | Status | HowTo | #00_0 | Four direct I/O lines | OK | GPIO | #00_1 | Three direct I/O lines and ground | OK | GPIO | #00_2 | Two direct I/O lines, +5V power, ground | OK | GPIO | #01 | Four-line RS232 port | OK | UART | #02 | RS232/422/485 port | OK | UART | #03_1 | Two low-power relays (configuration 1) | OK | GPIO | #03_2 | Two low-power relays (configuration 2) | OK | GPIO | #04_1 | Two isolated inputs | OK | GPIO | #04_2 | Three isolated inputs, common (-) | OK | GPIO | #04_3 | Three isolated inputs, common (+) | OK | GPIO | #04_4 | Four opto-inputs, common ground | OK | GPIO | #05 | RS485 port | OK | UART | #06 | Two high-power relays | OK | GPIO | #07 | Two solid state relays | OK | GPIO | #08 | Wiegand and clock/data reader port | OK | Wiegand | #09 | Low-power 5V supply, 12V input | OK | GPIO | #10 | Medium-power 5V supply, 12V input | OK | GPIO | #11 | Four open collector outputs | OK | GPIO | #12 | Low-power +15/-15V power supply, 5V input | OK | GPIO | #13 | Four-channel ADC | OK | I2C | #14 | Four-channel DAC | OK | I2C | #15 | High-voltage AC solid state relay | OK | GPIO | #16 | Three PWMs with open collector outputs | OK | I2C | #17 | Three PWMs with power outputs | OK | I2C | #18 | Power input | OK | None | #19 | DB9M connector | OK | None | #20 | Nine terminal blocks | OK | None | #21 | Four terminal blocks | OK | None | #22 | RTD Temperature Meter | UC | I2C | #23 | Isolated PoE power supply, 5V output | OK | None | #25 | High-power 5V supply, 12/24/48V input | OK | None | #26 | IR code processor | UC | I2C | #27 | IR receiver/transmitter | UC | SPI | #28 | Ambient light sensor | OK | I2C | #29 | Ambient temperature meter | OK | I2C | #30 | Ambient humidity meter | OK | I2C | #31 | PIC coprocessor | OK | I2C | #35 | Barometric pressure sensor | OK | I2C | #36 | 3-axis accelerometer | OK | I2C | #37 | RF connector | OK | None | #38 | Pushbutton | OK | GPIO | #39_1 | Large green LED (low brightness) | OK | GPIO | #39_2 | Large red LED (high brightness) | OK | GPIO | #39_3 | Large yellow LED (low brightness) | OK | GPIO | #39_4 | Large blue LED (high brightness) | OK | GPIO | #40_1 | Digital potentiometer, 5KOhm | OK | I2C | #40_2 | Digital potentiometer, 10KOhm | OK | I2C | #40_3 | Digital potentiometer, 50KOhm | OK | I2C | #40_4 | Digital potentiometer, 100KOhm | OK | I2C | #41 | 8-bit port | OK | I2C | #42 | RTC and NVRAM with backup | OK | SPI | #47 | GPRS modem | OK | UART | #52 | Four-channel isolated +/-10V ADC | OK | I2C | #53 | Isolated 4-20mA ADC | OK | I2C | #54 | Four dry contact inputs | OK | None | #56 | Type A USB port | OK | None | #57 | FPGA Tibbit | UC | SPI | #58 | Two 24V NPN isolated open collector outputs | OK | None | #59 | Two 24V PNP isolated open collector outputs | OK | None |
|---|